I have 21 of these switches and saw the same thing. Free Program Gaussview For Windows. I actually e-mailed support with this one before I posted here, and all they wanted to know is what is connected to the network.

Xmodem-1K, Ymodem, Ymodem-G. Download-xmodem-using-putty cacheddownload xmodem I. Project / source codes from CodeForge. Xmodem Console Download Procedure. It appears the older versions of boot code do. I was successfully able to downgrade back to 1.00.86 using the XMODEM method. SRW2024 Stuck in Loop after. Linksys SRW2040 Switch - corrupt firmware not able to restore. Downloading code using XMODEM. I have the srw2024 with firmware 1.0. There are not configuration commands for a guest. Downloading code using XMODEM. We've got an srw2024 v1.1 switch. If by chance you have flashed the wrong version.

My response was: '~250 XP PC's, 32 Sorensen IP video phones, several dozen HP print servers, a half dozen HP Servers with Win2003 Server, GTA firewall, and a handful of Cisco WiFi access points, not including one-off devices I can't recall.' Now, some inaccurate, but fast math with 21 switches in production should clue them into the fact that I have over 400 ports on this LAN, and recalling exactly what is connected to each one at any given moment is something few have time for. They then asked me the same question again - I told them that they wrote the firmware, and therefore the error message that gets logged, and it was time they explain to me where the error message comes from. I never heard back. I posted an identical question months ago here, and all I heard in response from the community is silence. The only thing I could think of was to isolate 1 switch, put a pair of PC's on it, and see if the Windows uPnP service was causing it to respond/generate errors.

Grc.com has a utility to kill the uPnP service on XP PC's, but I haven't had the time, nor a free switch to do this test with. I just reduced the log level flags so they fall behind the threshold, so I could see any other more important messages before rolloff.

If you find anything out, drop a note. When connected to the serial port the following continues to loop: ------ Performing the Power-On Self Test (POST) ------ UART Channel Loopback Test...PASS Testing the System SDRAM....PASS Boot1 Checksum Test....PASS Boot2 Checksum Test....PASS Flash Image Validation Test...PASS BOOT Software Version 1.0.0.03 Built 08-Jun-2004 09:48:10 CPU - FireFox 88E6218 ARM946E-S processor 64 MByte SDRAM. I-Cache 8 KB.

D-Cache 8 KB. Cache Enabled.

Autoboot in 2 seconds - press RETURN or Esc. To abort and enter prom. Preparing to decompress. Decompressing SW from flash HOSTG_rscode_file_load: could not load file Perform WARM BOOT. When I attempt to do download the new software with XModem the firmware (fw)completes successfully (ls20xx_Salsa-12222.ros) but the boot image fw fails (runtop_boot-101.rfb) and I receive this message: Startup Menu [1] Download Software [2] Erase Flash File [3] Password Recovery Procedure [4] Set Terminal Baud-Rate [5] Back Enter your choice or press 'ESC' to exit: Downloading code using XMODEM.

-- Download complete -- Wrong file format. Writing aborted. Is there a different version of the firmware perhaps an older version available for download somewhere? Or is there something I am doing wrong? Any help would be greatly appreciated. We have 2 - srw2024's and 2- srw2016's. Issue only on the one with the fw upgrade.

Hi Staff, Just a minor minor point for clarification, software version 1.1.2b or really 1.2.2b? Have you tried the following; step 1.

Added a IP address of 10.10.10. Amd 8515 Usb Lan Nic Driver here. X to that suspect switch. Step 2 saved the configuration change step 3.